Showing posts with label Bizen-ware. Show all posts
Showing posts with label Bizen-ware. Show all posts

Sunday, September 8, 2024

260. ŌIWA Tomoyuki, 1977- . black [Bizen-ware] sake-warming flask

260.  ŌIWA Tomoyuki 大岩智之. 1977- . Kuro tokkuri  黒徳利   (black [Bizen-ware] sake-warming flask)

 








For Ōiwa, see item no. 259. 

Dark gray clay. Fired unglazed, with natural ash glazing resulting in shiny black and matte black and dun colors. Weight: 426g (15 oz). Height: 13.8 cm (5-1/2 in).  Widths: rim, 3.5 cm (1-3/8 in); widest, 8.8 cm (3-1/2 in); base, 6 cm (2-3/8 in). 

This is shaped like a bottle gourd (瓢箪 hyōtan). It appears to have been molded on a wheel and then subsequently carved to form the belt, shoulders, neck, and rim. The main part of the body was then flattened slightly, leaving the piece longer from side to side. The maximum distance front to back is 8.2 cm, or about a quarter inch less the side-to-side dimension. 

The piece sits on the rim of the circular base, which was hollowed out in a shallow concavity. The remains of the three posts used to separate the piece from the kiln shelf during firing are visible on the bottom. The artist’s mark, a vertical line with a crossbar and a dot at the top right corner, is incised into the center of the base. The belt or waist begins about 5 cm (2 in) above the base and is one centimeter (3/8 in) wide. It consists of two horizontal grooves encircling the piece; the area between the two grooves was flattened with a carving tool. The lower bulge is a convex curve about 5 cm (2 in) in height, with the maximum width of 8.8 cm occurring 3.3 cm (1-1/4 in) above the base. The upper bulge is again a convex curve, with the maximum width of 7.5 cm (3 in) occurring 7 cm (2-3/4 in) above the base. Thus the widest area of both bulges is nearer the waist than the base or shoulders, respectively, of the piece. The shoulders begin 10.2 cm (4-1/8 in) above the base. The shoulder area is level, sloping slightly upwards toward the neck. At the neck’s lowest point, it is 2.5 cm (1 in) wide. The neck widens gradually up to the rim, which juts outward at a 90-degree angle and then slants slightly outward to the upper edge. The inside of the rim curves downward to the recessed mouth. It is impossible to see inside the piece. The surface of the exterior ranges from smooth over the heavily vitrified areas to a medium sandpaper grade on the relatively unglazed areas. 

This was fired unglazed. Some two-thirds of the exterior surface is covered with a vitrified ash glaze, with a dark black color. The base and some lower edges of the walls are a matte black color. Those portions of the exterior walls not covered with the vitrified ash glazing are a matte dun color.

 This came in a wooden box inscribed by Ōiwa in three lines: 黒 / 徳利 / sigil  kuro / tokkuri / sigil (black sake warmer-pourer / sigil), followed by the artist's seal stamped in red. See item no. 259 on the sigil. Included in the box were a gray wrapping cloth and a small card with a potted biography of the artist.  

This was sold as a unit with item no. 259, but the two pieces were not conceived as a set.  An online search found other similarly shaped tokkuri by Ōiwa. 

The irregularity of the main part of the body contrasts with the symmetry and precision of the pouring spout. The difference sets up a dialogue between the two parts. 

Purchased from the Kura Monzen Gallery in Kyoto in September 2024, who purchased it directly from the potter in June 2023 (invoice and shipping and customs documents).

Saturday, September 7, 2024

259. ŌIWA Tomoyuki. 1977- . black Bizen-ware drinking cup

 259. ŌIWA Tomoyuki 大岩智之. 1977- . Kuro guinomi 黒ぐい呑   (black [Bizen-ware] drinking cup)









Ōiwa Tomoyuki was born in Kobe, Hyogo prefecture, in 1977, and graduated from the Bizen Ceramic Center in 2004. The following year he became a student of the outsider Kakurezaki Ryūichi 隠崎隆一, with whom he would remain for eight years before going independent. In 2014 he built a half-submerged tunnel kiln (anagama), completing his first firing in 2015. He has since been featured widely and is known for his sake vessels. 

Glazed in dun brown and black. Weight: 158 g (5.6 oz). Height: 5.4 cm (2-1/8 in). Widths: mouth, 5.4 cm (2-1/8 in), widest, 6 cm (2-5/8 in); base, 5 cm (2 in). 

Any given horizontal cross-section of  this is roughly circular. The cup sits on a flat irregular foot ring. Before trimming, the base was probably completely flat. The inside of the base has been gouged out in a rough yin-ying pattern. The foot ring is level, and the cup rests stably on it. This came with a small white sticker with the number 11 on it attached to the base. Above the base the walls rise outward at about a 45-degree angle, to the widest point of the piece, about a centimeter (3/8 in) above the base. From the widest point to the mouth, the walls gradually sloped inward. There are wide, shallow horizontal grooves encircling the cup in this section. The mouth is generally even but has two small dips in it. There are tiny remnants of the three posts used to hold the piece away from the kiln shelves on the black side of the piece. The interior generally mirrors the exterior. The surface of the piece is smooth throughout and has the slight stickiness of a glazed work. 

The bottom, most of the interior, and half of the wall area were glazed in black. The other half of the walls and the lips of the mouth were glazed in a dun brown, which was allowed to drip into the black area of the walls along the horizontal grooves. Where the brown glaze thins out over the black glaze, it turned a light blue color. 

This came in a wooden box, inscribed by the artist in three lines: 黒 /ぐい呑 / sigil (black / small drinking cup //sigil), followed by the artist’s seal stampeed in red. Ōiwa’s sigil is indecipherable but appears to be the characters in his surname. Included in the box were a gray wrapping cloth and a small printed card with the artist’s potted biography. 

Purchased from the Kura Monzen Gallery in Kyoto in September 2024, who purchased it directly from the potter in June 2023 (invoice and shipping documents).

 

Friday, June 14, 2024

254. ISEZAKI Sō, 1968- , Bizen-ware squared sake server and cup

254. ISEZAKI Sō 伊勢崎創, 1968- , Bizen kaku shuki 備前角酒器 (Bizen-ware squared sake server and cup)














Isezaki Sō comes from a prominent family of potters in the Bizen tradition (his uncle Isezaki Jun is a Living National Treasure). He is the third son of the important potter Isezaki Mitsuru and was raised alongside the family kiln. At eighteen he apprenticed under Bizen master Yamashita Jōji and was first exhibited the following year. After his twentieth birthday he went to the United States for study. Upon returning to Japan, he won the first of many awards at the Okayama Kenten (Okayama Prefectural Art Exhibition). He then returned to the United States for another year of study. The American influences are apparent in his non-traditional approach to design. He has exhibited and received awards at the Nihon Dentō Kōgei Ten (Traditional Crafts Exhibition), the Tobiten of the Japan Ceramic Art Society, and the Tanabe Museum Modern Forms in Tea Exhibition, among others. For other examples of his work, see his website (SO ISEZAKI). 

Gray clay. Fired unglazed; surface colors in the red, tan, and brown ranges, with red veins of hidasuki 緋襷 (scarlet cords), with areas of vitrification. Server. Weight (without lid and handle): 396 g (14 oz). Height (of ceramic only): 7.2 cm (2-7/8 in). Length (overall): 13.8 cm (5-1/2 in). Width: 7.5 cm (3 in). Cup. Weight: 132 g (4.7 oz). Dimesions of cube: 5 x 5 x 5 cm (2 x 2 x 2 in). 

Both the server and the cup are squared off and angular in shape. The server has a wooden lid and a removable brass handle. The server is a rectangular box, with an attached spout and two semicircles that serve as anchoring points for the handle, one in the upper center of the back side and one at the front of the top side just aft of the spout. The box proper is 6.5 cm (2-5/8 in) high; 9.7 cm (3-7/8 in) long, and 7.5 cm (3 in) wide. The lower edges of the sides are beveled inwards at about a 30-degree angle to form a flat rectangular base, 5.8 x 8.2 cm (2-5/16 x 3-1/4 in), about 0.6 cm (1/4 in) high. The artist’s sigil is incised into the center of the base. The two anchoring points for the handle are 2.5 cm (1 in) wide and 1 cm (3/8 in) high. The spout is a right triangle set flush with the top side of the box and located in the upper center of the front side. It is 3.1 cm (1-1/4 in) high, 2.7 cm (1-1/8 in) long, and 1.5 cm (5/8 in) wide. The pouring hole is a rectangle. The opening on the top of the box is another rectangle, located at the rear of the piece, 6.6 x 4.8 cm (2-5/8 x 1-7/8 in) in size. The lid is made of a fine-grained wood, 7.4 cm (2-15/16 in) square. The underside of the lid has a protruding rectangular piece slightly smaller than the hole in the top of the box that serves to anchor the lid on the box. The surface texture if the piece is slightly rough, like a fine-grained sandpaper. 

The cup is a rough cube, with irregular top edges. The bottom edges of the sides are beveled inwards at about a 45-degree angle. The cup sits on a flat base, roughly 4.2 cm (1-5/8 in) square. The center of the base is a shallow, squarish depression of irregular depth (at most one mm deep). The artist’s sigil is incised in this area of the base. The walls of the cup are covered with a series of very shallow striations, angling toward the left. The texture of the cup ranges from very smooth in the areas covered by vitrified ash glazing to slightly rough in the uncovered portions.

These were fired unglazed. Both pieces show the red hidasuki veins, produced by the interaction between rice straw and the Bizen clay. These are found on the bottom of the server and the bottom and sides of the cup. The bottoms of both pieces are otherwise largely the natural color of the clay. On the sides, kiln effects left colors in the tan, reddish brown, and dark brown ranges. On the server, the back side and the two long sides have large areas of vitrification from natural ash glazing. The sides of the cup are mostly covered with vitrified ash glazing. In some places this layer is quite heavy and thick. 

This came in a well-constructed, two-chamber box. The front of the box was inscribed by Isesaki in three lines: 備前 / 角酒器 / 創  Bizen / kaku shuki / Sō (Bizen-ware / square sake set / Sō), followed by the artist’s seal in red. Included in the box were a small printed biography and two dark blue wrapping cloths. 

Purchased from the Kura Monzen Gallery in Kyoto, Japan, in June 2024 (invoice, shipping and customs documents).

Sunday, June 9, 2024

253. WATANABE Takuma, 1968­- , Bizen-ware drink server

253. WATANABE Takuma 渡邊琢磨, 1968­- , Bizen shuki   備前酒器  (Bizen-ware drink server), “Mirai no kaseki” ミライノカセキ (Future fossils) series, no. 151

 










For Watanabe, see item no. 231. 

Red clay, unglazed, with kiln effect colors in the dark reddish brown and dark gray colors. Weight: 292 g (10 oz). Height: 8.5 cm (3-3/8 in). Length: 15 cm (6 in). Width: 9 cm (3-5/8 in). 

This sits on a flat, circular base, 3.8 cm (1-1/2 in) in diameter. The center of the base is a shallow concavity. The artist’s sigil was incised into this area (see item 252 for the sigil). The body is egg-shaped with a katakuchi-style pouring spout. The egg is roughly 10.7 cm (4-1/4 in) long. The spout is located about three-fourths of the way up the body. As with other pieces in the Future Fossils series, the surface decoration copies features of old machinery. The surface is divided by faint lines into “plates” held together by screws. Protruding from the surface are molded switches, dials, conduits, braided cords, vents, and meters. A rectangular label inscribed “S 151” identifies this piece’s place in the series. The exterior texture is smooth; the interior has a grain like medium sandpaper. 

Fired unglazed. Most of the surface is a uniform dark gray. The bottom and the back side are a dark red. The piece was probably fired with the spout facing the heat and ash flow. 

This came in a wooden box inscribed by Watanabe in two lines: 備前酒器 / 琢磨  Bizen shuki / Takuma  (Bizen-ware drink server / Takuma), followed by the artist’s seal stamped in red (the seal has the seal form of the character 琢). Included in the box were a dark blue wrapping cloth and a potted biography. 

Purchased from Kura Monzen Gallery in Kyoto, Japan, June 2024 (invoice, shipping and customs documents)

Saturday, June 8, 2024

252. WATANABE Takuma , 1968- , Bizen-ware sake cup

252.  WATANABE Takuma 渡邊琢磨, 1968- , Bizen sake-nomi  備前酒呑   (Bizen-ware sake cup)











For Watanabe, see item no. 231. 

Dark gray clay. Unglazed; surface colors in dark mahogany reds, grays, and black, with some vitrified natural ash glazing on the exterior. Weight: 110 g (4 oz). Height: 5 cm (2 in). Width: 6 cm (2-3/8 in). 

This sits on a roughly circular foot ring, 4.3 cm (1-3/4 in) in diameter and about 0.15 cm (1/16 in) high on the exterior. The interior of the foot ring was hollowed out to a depth of around 0.3 cm (1/8 in). Above the foot ring, the base juts out at about a 45-degree angle to the width of the cup. The artist’s sigil, |+<, was incised into this area of the cup. The proper orientation of the mark isn’t clear, but it appears from the buildup of the clay at the ends of the lines and its placement that it is to be viewed either in the way shown above or with the long line as the base. The walls rise in more or less straight lines, curving slightly inward at the rim. The exterior walls were shaped in a series of vertical panels. Each panel is decorated, either with carved geometric shapes in extremely shallow relief or with shallow striations. The interior mirrors the shape of the exterior. The surface is fairly smooth, with the exception of the rim, which is rather rough for a piece of this nature. 

This was fired unglazed. The surface colors are the results of kiln effects. Much of the exterior surface is covered with a sheen of vitrified natural ash glazing. 

This came in a wooden box, inscribed by Watanabe in two lines: 備前酒呑 / 琢磨 Bizen sake-nomi / Takuma (Bizen-ware sake cup / Takuma), followed by the artist’s seal stamped in red (the seal form of 琢). Included in the box were a dark blue wrapping cloth and a potted biography of the artist. 

This piece is not part of Watanabe’s Future Fossils series, but its surface decorations share many characteristics with those found on the pieces in that series. 

Purchased from Kura Monzen Gallery in Kyoto, Japan, June 2024 (invoice, shipping and customs documents)

Wednesday, March 27, 2024

243. Bizen-ware "gold dust pouch" water container

243.  Bizen-ware water container for the tea ceremony 古備前耳付砂金袋水差  ko Bizen mimitsuki sakinbukoro mizusashi  (old[-style] Bizen-ware “gold dust pouch” water container, with ear lugs)










Roman Nikolaev, the seller, dates this to the 1950s. Here, the 古 in the inscription on the box refers not to the age of the piece but to the style of Bizen-ware. This imitates the older methods of making and firing Bizen-ware, which were revived in the twentieth century. Rather than a pottery lid (a 共蓋 tomo-buta) made of the same clay as the base, this has a black lacquered wooden lid (a 替蓋  kae-buta). 

Dark reddish brown clay, with natural-ash glazing on the exterior, with many patches of goma 胡麻, yellow sesame-seed-like deposits of ash, and some blackening of the exterior surface; the interior has no glazing. Weight: overall, 1680 g (3.75 lb); body, 1630 g (3.6 lb); lid, 50 g (1.8 oz). Height: 17.3 cm (6-7/8 in). Width: mouth, 9.8 cm (3-7/8 in); lip, 14.2 cm (5-5/8 in); narrowest, 10.3 cm (4-1/8 in); widest, 17.4 cm (6-7/8 in); base, 13.2 cm (5-1/4 in). 

This is shaped like a drawstring bag. It sits on the flat base, which is about 1 cm (3/8 in) thick. At one edge of the base, a small circle with an interior bar was incised into the clay; this may be a kiln mark. The surface of the base is lightly scored with lines, some of which continue up the sides of the piece. The walls extend upward in a convex arc, with the widest point occurring about 3.8 cm (1-1/2 in) above the base, extending to the narrowest width 10.7 cm (4-1/4 in) above the base. There is a pronounced groove encircling the pot at the narrowest width. Above this, the walls rise outward in a shallow arc to the lip. The body of the pot has horizontal striations at fairly regular intervals, perhaps remnants of finger marks if this was thrown on a wheel, or of the coils of clay if this was hand-shaped. The front of the pot has a large, irregular dent in the center, These striations are much more pronounced in the upper part of the body. Four deep vertical grooves were incised into the pot, two each on the front and the back, in the bottom section of the pot. There is another deep groove encircling the pot, at an irregular height above the base, just below the places where the bottoms of the ear lugs are attached. In contrast to most ears on Japanese pots, the widest points of the ears are at the lower end rather than the upper. The tops of the ears are 13.8 cm (5-1/2 in) and the bottoms 7.6 cm (3 in) above the base. The lid sits on a recessed gallery. The interior of the pot mirrors the shape of the exterior. The surface is relatively smooth. 

This was fired unglazed. All the surface colors and effects resulted from natural-ash glazing, ash deposits, and kiln effects. Most of the goma occur on the front of the piece. 

Like a drawstring pouch, this sags toward the base, a movement mirrored in the ear lugs, which also sag downward. “Gold dust” may be a nod to the golden goma spots. 

This came in a wooden box, inscribed in two lines, 古備前 / 耳付砂金袋水差  ko Bizen / mimitsuki  sakinbukoro mizusashi  (old[-style] Bizen-ware / “gold dust pouch” water container, with ear lugs). A paper strip pasted on the side of the box reads 備前焼 Bizenyaki  (Bizen-ware).

\Purchased from Treasures of Old Times, Perth, Australia in March 2024 (invoice, customs documents).

 

 

Pottery

Looking for suggestions

I need to dispose of my collection. I've tried to donate it to several local museums or schools with ceramics programs, but no one wants...